Tag Archives: Foam

How to Make a Foam Flower

Homemade foam flowers make excellent decorations for parties. Making them is simple, so it’s a great project to do with kids. Craft stores and dollar stores carry all the supplies you need to make these colorful creations. Read on to learn how to make foam calla lilies, violets and mums.

Edit Steps

Calla Lily

  1. Cut a circle out of a sheet of foam. This will become the calla lily bloom. The circumference of the circle can be as small or as large as you want.

  2. Fold the circle in half. Make sure it’s folded neatly, so that the shape of the calla lily will turn out right.

  3. Alter the circle to create a rounded heart shape. Start by placing the scissors at the bottom point of the folded foam. Cut along the edge of the circle, then dip the scissors in at the top of the circle to make a rounded edge. when you unfold the circle, it should look like a rounded heart, with two subtle humps at the top; the bottom of the heart should remain rounded.

    • The classic heart shape has a sharply pointed bottom tip, but in this case you want to keep the bottom rounded with a slight point.

    • Don’t make the humps at the top too pronounced; they should be subtle.

  4. Make a small slit between the humps. This will make it easier to from the foam into the cylindrical shape of a calla lily bloom.

  5. Cut a yellow pipe cleaner in half, then fold it in half. Twist the two ends together. This will become the lily’s stamen, which juts realistically out from the center of the bloom.

  6. Glue the pipe cleaner in the cleft between the two humps. Put a dab of hot glue just between the two humps above the slit, and lay the folded pipe cleaner on top so that the folded end sticks up toward the point of the lily boom. The twisted ends should jut out past the cleft by about 1/2 inch.

  7. Gather the lily bloom around the pipe cleaner. Put a dab of hot glue on the front of the yellow pipe cleaner right at the cleft in the lily bloom. Take the two sides of the lily bloom (right where you made the slit) and pinch them together in front of the pipe cleaner, pressing them down so that they stick to the hot glue dab. You can add an extra dab of hot glue between the sides to help them stay in place.

  8. Make a stem out of a green pipe cleaner. Wrap the top of the pipe cleaner around the base of the yellow pipe cleaner, so that the yellow is completely obscured. Leave the tail of the green pipe cleaner straight, so it resembles a stem.


  1. Cut a circle from a purple piece of foam. Use purple foam if you want to make a violet, but other colors are fine if you’d like to make a different type of flower.

  2. Cut slits around the circle. Cut evenly-spaced slits from the edge of the circle toward the middle, stopping about 1/2 inch short of the center.

  3. Cut “v” shapes out of the petals. Lift each petal and cut an inverted “v” shape by making two diagonal cuts.

  4. Cut a small circle out of white foam. This will be the center of the flower.

  5. Glue the circle to the center. Place a dab of hot glue in the center of the violet, then stick the small white circle to the glue.

  6. Scrunch the flower petals. Pinch each flower petal in half vertically, so they stand up a bit and created a 3-D effect, rather than lying flat.

  7. Glue the stem to the back of the flower. Use a green pipe cleaner as the stem, and glue the top to the back of the flower’s center.


  1. Cut a foam square in half. Choose any color you’d like, since mums come in a variety of hues.

  2. Create a loop. Put a line of hot glue across the bottom of the foam, then stick the top of the foam sheet to the glue.

  3. Cut fringe. Cut strait lines from the folded part of the loop toward the glued edges. Stop cutting before you get to the glue line. Continue until you’ve made fringe all the way across.

  4. Roll the foam. Begin at one short edge and roll the foam to the opposite end. When the roll is complete, dab some hot glue along the opposite end and press it down against the roll. Now start with one end of the foam and begin to roll to the opposite end.

  5. Open the flower. When the glue dries, use your fingers to open the flower by pulling out the “petals.” Press each petal in the center so that it opens. Continue fluffing out the petals until the flower looks complete.

  6. Add a stem. Place a dab of glue in the center of the bottom of the mum. Lay the end of the pipe cleaner on the glue and hold it in place until the glue dries.

  7. Finished.

EditThings You’ll Need

  • Sheets of foam
  • Pipe cleaners
  • Hot glue gun and glue sticks
  • Scissors

Edit Video

Article Tools

How to Make a Foam Netting and Plastic Bottle Lantern

Make an easy lamp by recycling a plastic bottle and the protective foam netting often found wrapped around bottles or soft produce. This lamp throws a lovely glow and would look lovely when added to a dinner party or other special occasion. As with any candle usage, just be sure to keep an eye on it when using.

Edit Steps

  1. Cut off the top of the bottle to the base of its neck. Cut off the base as well. See image for the cutting proportions. This will form a cylinder from the bottle.

  2. Prepare the foam netting. Cut to fit around the cylinder. Most importantly, it should not exceed the height of the bottle. As such, measure to ensure that it us under the neck end and above the base end.

  3. Cut the netting end. As shown in the image, trim the edge to ensure that it looks neat and pretty, with all the angles aligned and even.

  4. Place the prepared foam netting around the plastic cylinder. Adjust to ensure that it is sitting straight.

    • Add a tea light into the center of the lamp, on the spot where you’re going to use it. It might be easier to place it on a plate or other portable surface for ease of movement; that’s optional though.
    • Read the “Warnings” below on fire safety.
    • Light the tea light. Enjoy the pretty glow.

Edit Tips

  • To enhance the color of the lamp, you can weave cellophane paper in and out between the holes of the foam netting.

    The end result will be a glow the color of the cellophane used, ideal for matching the color theme of a party.

  • You can also replace the LED light source. (Refer to the Video)

Edit Video

Light source:Multicolor LED rotated lamp

Edit Warnings

  • Notes on fire prevention:
  • Put the candle in the exact center, well away from the cylinder’s walls.
  • Ensure that the the top of the bottle is open and free of obstruction.
  • Double check that the foam netting is not sitting above the height of the bottle in any way.
  • Only use this lantern in a place where there is no breeze or wind; it will topple and potentially burn if there is a breeze or wind blowing on it.

Edit Things You’ll Need

  • Plastic bottle (500ml)
  • Foam netting (also known as fruit foam sleeve, fruit foam netting, bottle netting, foam plastic protective net, etc.)
  • Tea light candle
  • Scissors
  • Items needed for this project.

    Items needed for this project.


  • Color cellophane (optional)

Edit Related wikiHows

Article Tools